6YL-160型螺旋榨油机主要性能参数
一．主要性能参数:
Main Specifications
1.榨轴转速:35-39转/分
Shaft speed: 35-39r/m
2.齿轮箱传动比:15/38/15/52=1:8.78
Gear ratio in gearbox: 15/38/15/52=1:8.78
3.配用动力: 18.5-22KW
Motor: 18.5-22KW
4.三角带: B型
Belt: B型
5.外形尺寸:长x宽x高 2020x700x1480(mm)
Outer dimension: L×W×H(mm) 2020x700x1480
6.单机重量: 960kg
Weight: 960kg
7产量: 14-17吨
Output:14-17T/D
6YL-160型螺旋榨油榨笼(包括条排,圆排,骨圈)的拆装方法
Assembly/disassembly of Pressing cage (round plates, square rods holder)
| 序号NO | 品名name | 厚度mm thickness | 备注note | 序号NO | 品名name | 厚度mm thickness | 备注note |
| 1 | 1＃圆排pressing ring | 30 | 两面米子牙倒角miziya angle of chamber | 15 | 15＃圆排pressing ring 5 | 70 |
|
| 2 | 2＃圆排pressing ring No.2 | 30 |
| 16 | 16＃圆排pressing ring 5 | 30 | 平面倒角 Plane angle of chamber |
| 3 | 3＃圆排pressing ring No.3 | 30 |
| 17 | 17＃圆排pressing ring 5 | 25 |
|
| 4 | 4＃圆排pressing ring No.4 | 30 |
| 18 | 18＃圆排pressing ring 5 | 30 |
|
| 5 | 5＃圆排pressing ring No.5 | 30 | 米子牙倒角 Miziya angle of chamber | 19 | 19＃圆排pressing ring 5 | 30 |
|
| 6 | 6＃圆排pressing ring No.6 | 70 |
| 20 | 20＃圆排pressing ring 5 | 30 | 米子牙倒角 Miziya angle of chamber |
| 7 | 7＃圆排pressing ring No.7 | 30 | 平面倒角 plane angle of chamber
| 21 | 出饼圈cake output ring |
|
|
| 8 | 8＃圆排pressing ring No.8 | 25 |
| 22 | 压紧丝pressing bolt |
|
|
| 9 | 9＃圆排pressing ring No.9 | 30 |
| 23 | 条排pressing bar |
|
|
| 10 | 10＃圆排pressing ring 0 | 25 |
| 24 | 条排圈rail group ring |
|
|
| 11 | 11＃圆排pressing ring 1 | 30 |
| 25 | 上榨笼top cage |
|
|
| 12 | 12＃圆排pressing ring 2 | 30 |
| 26 | 榨笼短键pressing cage minor key |
|
|
| 13 | 13＃圆排pressing ring 3 | 30 |
| 27 | 下榨笼bottom cage |
|
|
| 14 | 14＃圆排pressing ring 4 | 30 | 米子牙倒角 Miziya angle of chamber | 28 | 榨笼长键pressing cage major key |
|
|
2.榨螺的拆装方法：
（1）榨螺的拆法：停机后立即搬动手柄，把榨轴从榨膛内抽出，卸下保护帽、六方螺母、园螺母及调节螺栓，用直径16的铁棒插入锁紧螺母的孔内顺时针方向旋转（切记与轴芯配合的螺纹均为左旋），拆去紧锁螺母后，各节榨螺即可卸下。如榨螺（内孔进有细渣）因阻塞不好拆卸，可将地上垫一木板，二人将榨螺轻撞几 下即可卸下，若仍卸不下来，可用木柴火加热后再卸下。
（2）榨螺的安装：将榨螺立起细端向上，装上档圈，在把榨螺由1号起依次装于轴上，然后用锁紧螺母压紧，以防油渣深入榨螺孔内，影响榨螺的拆卸。（调节螺母使调节栓两端是8309轴承，装时两轴承大孔面均靠在调节螺栓的两端面。榨螺整体装齐后用两个（M42×2）的螺帽背紧，背紧时注意两个8309轴承的缝隙 。用手搬转调节螺栓，感到转动灵活时即可。
5．2 Pressing screw：
5．2．1 Disassembly of the screw ：rotate the handle as soon as machine stops and pull out the screw from the chamber ，remove nuts and adjusting bolt. Insert a 16mm diameter bar into lock nut and turn and turn it clockwise.(important note: left hａnd screw).After taking off lock nut, each part of pressing screw can be removed. However, holes in the screw might be blocked by fine slag particles, which retard the disassembly. Tapping or heating pressing screw might help disassembling.
5.2.2 Mounting pressing screw :put small end of its shaft upwards, mount the first screw and then the second...sequence, tighten then by the lock nut to avoid particles in . On both ends of adjusting bolt, which is easily swung on the shaft by adjusting nut, two bearing 8309 are mounted. Be careful to make big hole sides of these two bearings touch adjusting bolts double ends. Finally , whole pressing screw will be tightened by two M42×2 nuts, But certainly, gaps of two bearings need to be carefully set. In fact, if hands can swing adjusting bolts smoothly, the adjustment is acceptable.
