zui大流量: 100 m³/h
zui大扬程: 80 m
zui大进口压力: 4 bar SolidC标准工况卫生离心泵
采用同一尺寸的机械密封，与LKH 单端面机封*.
标准设计：
SolidC泵适用于标准负载应用领域，适用CIP（原位清洗）解决方案、公用事业、水（处理、加热、冷却）、洗衣机、工作范围内的流体输送等。
SolidC适用在食品、奶制品、饮料、个人护理用品、制药、清化工和水工业使用。
标准设计：
SolidC泵由标准电机、短轴、机械式压紧联轴节、接头、支承板、叶轮、泵盖和轴封组成。
SolidC 性能
限于已经验证的应用领域：奶制品、CIP供水和葡萄酒。
限于已经验证的应用领域：奶制品、CIP供水和葡萄酒。
SolidCL Pump
Applications
The SolidCL pump is designed for standard duty applications, like
pumping CIP （Cleaning In Place） solutions, utilities, water （processing,
heating, cooling）, washing machines, simple transport duty within
working range. SolidCL is suited for use in the food, dairy, beverage
and water industries.
Standard design
The SolidCL pump consists of a standard motor, stub shaft,
mechanical compression coupling, adaptor, back plate, impeller, pump
casing and shaft seal.
The SolidCL pump is designed for CIP with emphasis on large internal
roundings and cleanable seals.
SolidCL has a stainless steel shroud for protection of the motor, and
the complete unit is supported on four adjustable legs.
Shaft seals
The SolidCL pump is equipped with either an external single or a
flushed shaft seal. Both have stationary seal rings in acid-resistant steel
AISI 329 with sealing surface in silicon carbide and rotating seal rings in
carbon. The secondary seal of the flushed seal is a long lasting lip seal.
Materials
Productwetted steel parts: . . . . . . . . .Acid-resistant steel 1.4403
（304L）.
Other steel parts: . . . . . . . . . . . . . . .Stainless steel 1.4301 （304）.
Finish: . . . . . . . . . . . . . . . . . . . . . .Blasted （standard）
3A polishing （Ra 0.8）.
Productwetted seals: . . . . . . . . . . . .EPDMrubber （acc. to FDA）.
Technical data
Max. inlet pressure: . . . . . . . . . . . . .400 kPa （4 bar）.
Temperature range: . . . . . . . . . . . . . .-10°C to +120°C （EPDM）.
Flushed shaft seal （FSS）:
Water pressure inlet: . . . . . . . . . . . . .max. 100 kpa （1 bar）.
Water consumption: . . . . . . . . . . . . .0.25 -0.5 l/min.
Connections for FSS:
R 1/8" （BSP） external thread.
Motor
Foot-flanged motor according to the IEC metric standard （EFF II）, 2
poles = 3000/3600 rpm. at 50/60 Hz, IP 55 （with drain hole with
labyrinth plug）, insulation class F.
Voltage and frequency
3 ~, 50 Hz, 220-240V Δ/380-420VY ≤ 4 kW
3 ~, 60 Hz, 250-280V Δ/440-480VY ≤ 4.6 kW
3 ~, 50 Hz, 380-420V Δ/660-690VY ≥ 5.5 kW
3 ~, 60 Hz, 440-480V Δ ≥ 6.4 kW
Motor sizes
50 Hz: 1.1, 1.5, 2.2, 3, 4, 5.5, 7.5, 11, 15, 18.5 kW
60 Hz: 1.3, 1.75, 2.5, 3.5, 4.6, 6.4, 8.6, 12.5, 17, 21 kW.
Warranty
Extended 3-years warranty on the SolidCL Centrifugal Pump range.
The warranty covers all non wear parts on the condition that genuine
Alfa Laval Spare Parts are used.
OC TOB E R 2008
The SolidCL pump is designed for standard duty applications, like
pumping CIP （Cleaning In Place） solutions, utilities, water （processing,
heating, cooling）, washing machines, simple transport duty within
working range. SolidCL is suited for use in the food, dairy, beverage
and water industries.
Standard design
The SolidCL pump consists of a standard motor, stub shaft,
mechanical compression coupling, adaptor, back plate, impeller, pump
casing and shaft seal.
The SolidCL pump is designed for CIP with emphasis on large internal
roundings and cleanable seals.
SolidCL has a stainless steel shroud for protection of the motor, and
the complete unit is supported on four adjustable legs.
Shaft seals
The SolidCL pump is equipped with either an external single or a
flushed shaft seal. Both have stationary seal rings in acid-resistant steel
AISI 329 with sealing surface in silicon carbide and rotating seal rings in
carbon. The secondary seal of the flushed seal is a long lasting lip seal.
Materials
Productwetted steel parts: . . . . . . . . .Acid-resistant steel 1.4403
（304L）.
Other steel parts: . . . . . . . . . . . . . . .Stainless steel 1.4301 （304）.
Finish: . . . . . . . . . . . . . . . . . . . . . .Blasted （standard）
3A polishing （Ra 0.8）.
Productwetted seals: . . . . . . . . . . . .EPDMrubber （acc. to FDA）.
Technical data
Max. inlet pressure: . . . . . . . . . . . . .400 kPa （4 bar）.
Temperature range: . . . . . . . . . . . . . .-10°C to +120°C （EPDM）.
Flushed shaft seal （FSS）:
Water pressure inlet: . . . . . . . . . . . . .max. 100 kpa （1 bar）.
Water consumption: . . . . . . . . . . . . .0.25 -0.5 l/min.
Connections for FSS:
R 1/8" （BSP） external thread.
Motor
Foot-flanged motor according to the IEC metric standard （EFF II）, 2
poles = 3000/3600 rpm. at 50/60 Hz, IP 55 （with drain hole with
labyrinth plug）, insulation class F.
Voltage and frequency
3 ~, 50 Hz, 220-240V Δ/380-420VY ≤ 4 kW
3 ~, 60 Hz, 250-280V Δ/440-480VY ≤ 4.6 kW
3 ~, 50 Hz, 380-420V Δ/660-690VY ≥ 5.5 kW
3 ~, 60 Hz, 440-480V Δ ≥ 6.4 kW
Motor sizes
50 Hz: 1.1, 1.5, 2.2, 3, 4, 5.5, 7.5, 11, 15, 18.5 kW
60 Hz: 1.3, 1.75, 2.5, 3.5, 4.6, 6.4, 8.6, 12.5, 17, 21 kW.
Warranty
Extended 3-years warranty on the SolidCL Centrifugal Pump range.
The warranty covers all non wear parts on the condition that genuine
Alfa Laval Spare Parts are used.
OC TOB E R 2008
Options
A. Impeller with reduced diameter.
B. Motor for other voltage and/or frequency.
C. 1500 rpm. motor.
D. Flushed shaft seal.
E. Product wetted seals of Nitrile （NBR）, Fluorinated rubber （FPM）
or FEP.
F. Rotating seal ring of Silicon Carbide.
Ordering
Please state the following when ordering:
- Pumpsize.
- Connections.
- Impeller diameter.
- Motor size.
- Voltage and frequency.
- Flow, pressure and temperature.
- Density and viscosity of the product.
- Options.
Note!
For further details, see also ESE00232.
This product has EHEDG certification.
A. Impeller with reduced diameter.
B. Motor for other voltage and/or frequency.
C. 1500 rpm. motor.
D. Flushed shaft seal.
E. Product wetted seals of Nitrile （NBR）, Fluorinated rubber （FPM）
or FEP.
F. Rotating seal ring of Silicon Carbide.
Ordering
Please state the following when ordering:
- Pumpsize.
- Connections.
- Impeller diameter.
- Motor size.
- Voltage and frequency.
- Flow, pressure and temperature.
- Density and viscosity of the product.
- Options.
Note!
For further details, see also ESE00232.
This product has EHEDG certification.
